Filament Dry Box Humidity Keeps Rising? Here’s What to Check

If humidity rises after drying, compare readings at the same temperature. Then test the box empty and with a spool to narrow down the cause.

By XUCHUN

Filament Dry Box Humidity Keeps Rising? Here’s What to Check

XUCHUN

Filament Dry Box Humidity Keeps Rising? Here’s What to Check

The humidity display drops during drying. By the next morning, it’s higher again. Before running another cycle, check the temperature next to the humidity reading. A warmer box can show a lower relative humidity than the same box after it cools, even if the amount of water vapor in the air hasn’t changed. U.S. National Weather Service guide to relative humidity

A filament dry box hygrometer measures the air around the spool. To find out why the reading keeps rising, first compare it at similar temperatures. Then check whether the pattern appears with the spool removed, with the spool inside, or only while you’re feeding filament.

Start with a reading after cooldown

Write down the box temperature and relative humidity together. If you have a heated model, take a second reading once the drying cycle has ended and the box temperature has stabilized. Compare that reading with a later one taken at roughly the same temperature, with the lid closed between checks.

A jump during cooldown can come from the temperature change alone. A steady rise after the temperature has stabilized gives you a reason to check the enclosure, the desiccant, or the spool. U.S. National Weather Service guide to relative humidity

Run an empty-box test, then add the spool

  1. Check the box without a spool. With heating off, remove the spool and inspect the lid seal. Close unused filament outlets as the box maker directs. If the box supports desiccant, use a fresh or properly regenerated pack. Latch the lid and note whether humidity falls and stabilizes at room temperature.
  2. Repeat with the spool inside. Keep the box in the same place and use the same sensor and desiccant. Opening the lid lets room air in, so allow the reading to settle before comparing it with the empty-box result.
  3. Check the feed setup separately. If the box holds a stable reading in storage but rises while printing, inspect the guide tube, outlet fittings, and unused ports. Check whether you’re opening the lid during the job or whether the room temperature changes while the printer runs.

Prusa’s drybox documentation identifies improper sealing, frequent opening, and depleted desiccant as factors that can affect internal humidity. Follow your own box maker’s instructions for the outlet and any vents used during heated drying. Prusa USS Drybox guide

What you observe What to check next
Humidity rises mainly as the box cools Compare later readings at similar temperatures before changing anything.
The empty box won’t settle with fresh desiccant Inspect the gasket, latches, and unused outlets. If the reading still looks implausible, compare it with a second hygrometer in the same space.
The empty box stabilizes, but the reading rises again with the spool inside The filament or spool may be releasing moisture. If the print also shows popping, bubbles, or rough extrusion, try the filament maker’s drying cycle and repeat the same print.
Humidity rises only while feeding filament Check the outlet and guide tube in the printing configuration. Compare the temperature during printing with the temperature during storage.

Popping, bubbles, and rough surfaces can be signs of moisture. A before-and-after print with the same file and profile gives you a better check than the air reading alone. Prusa filament drying guide · INKCLOUD troubleshooting FAQ

Know when to run another drying cycle

If the spool prints cleanly and the cooled box holds steady, keep that reading as a reference for the next check. If the loaded box repeatedly climbs at a stable temperature and print quality improves after an approved drying cycle, record the material, cycle, and result so you can repeat what worked.

The INKCLOUD Filament Dry Box is listed as a 4 L unit with active drying, temperature and humidity monitoring, and a direct-feed outlet. For heated drying, use the schedule specified for your exact filament and stay within the limits of the spool and device. For a passive box, use it to protect filament during storage or feeding, and use a suitable dryer when the spool needs active drying. INKCLOUD Filament Dry Box · Prusa USS Drybox guide

Frequently asked questions

What humidity should I aim for?
Use the storage guidance for your filament and box. Record the stable reading with a spool that prints well so you have a reference for future checks.

How do I know when to replace the desiccant?
Use its saturation indicator if it has one, or repeat the empty-box test with a fresh pack. If the reading settles with the fresh pack under the same conditions, the old one may be depleted. Follow the desiccant maker’s instructions for replacement or regeneration. Prusa USS Drybox maintenance guide

Can a low reading prove the filament is dry?
A low reading tells you the air inside the box is relatively dry at that temperature. Use the filament maker’s drying guidance and a short test print to judge whether the spool is ready. Prusa filament drying guide

Explore the INKCLOUD Filament Dry Box for monitored storage, active drying, and direct feeding.

Zurück Weiter
Kommentar hinterlassen 0 Kommentare

    Weitere Artikel lesen