TPU 95A Flexible Filament: How to Print Grippy Feet with the Right Amount of Give?
XUCHUNTPU 95A Flexible Filament: How to Print Grippy Feet with the Right Amount of Give
A foot pad that feels soft between your fingers can still feel firm under a desktop stand. A pad that compresses easily might let the stand rock. The easiest way to find the right balance is to print a few small samples and test them where they’ll actually be used.
TPU 95A flexible filament is a thermoplastic polyurethane with a nominal hardness of 95 on the Shore A scale. That rating describes how the material resists indentation. The feel of a printed pad also depends on how much material sits under the load and how it’s arranged. Wall count, infill, and the thickness of the top and bottom layers all give you ways to tune flexibility from the same spool. INKCLOUD flexible filament guide · Prusa flexible materials guide
Print three pads with the same footprint
Start with a simple pad for a lightweight desktop accessory. Use the same outer dimensions, bottom texture, print orientation, and filament profile for all three samples. Keep the top and bottom layer settings fixed so you can see what changes when you adjust the interior.
| Sample | What to change | What to check |
|---|---|---|
| A — Baseline | Use your current TPU profile and record its wall count and infill. | Does the pad compress enough to take up slight unevenness while keeping the stand steady? |
| B — Lower infill | Reduce infill density while keeping the pattern and wall count the same. | Does it give more under the same load? Does the top sink or tilt? |
| C — More walls | Use Sample B’s infill settings and add one wall. | Does the edge hold its shape better? Is there still enough give under the stand? |
Check the slicer preview before printing. In a very small pad, walls can fill most of the part, leaving little infill to adjust. If the previews for A and B look nearly identical, try a wider sample or test wall count first. Prusa guide to layers and perimeters
Test compression, recovery, and grip separately
- Compression. Place each pad under the same load, applied over the same area. Check how far it settles and whether one edge collapses. For a stand with several feet, print a matching set of the best candidate and check for rocking.
- Recovery. Remove the load after the same amount of time for each sample. Compare their unloaded heights and look for a lasting dent. If the device will sit on the pads for days at a time, give your chosen design a longer trial under its normal load.
- Grip. Test the pad on the actual surface, such as a laminate desk or painted shelf. Apply a gentle sideways push under the normal load. Watch both contact points. The pad can slide against the desk, or the stand can slide against the pad.
If the pad compresses the way you want but still slides, keep its internal structure for the next test. Change only the slipping contact surface, such as the bottom texture or how the stand seats on top, and repeat the check.
Keep the print settings consistent
INKCLOUD lists 210–240°C nozzle temperature, 30–35°C build plate temperature, and 50–100 mm/s print speed for its TPU 95A. The product page also lists 50 ± 5°C for 4–8 hours for pre-print drying in a filament dryer. Use these as product-specific references and follow the guidance for your printer and build plate. If a sample has gaps or visibly uneven extrusion, fix the print quality and rerun it before comparing how it compresses. INKCLOUD TPU 95A print settings
Frequently asked questions
Can I make a 95A pad softer without changing filament?
Yes. Try less infill or fewer walls, one change at a time. How much difference you feel depends on the size of the pad and where the load lands. Prusa flexible materials guide
Should I add open channels like the ones on the cover?
Open channels are an option once you know how much give you want. Print one sample and check the channel roofs for sagging. If they print poorly, try an arch-shaped opening or a different print orientation, then repeat the load test.
Which pad should I choose?
Choose the pad that keeps the accessory steady, grips the intended surface, and recovers enough for the way you use it. For a desktop stand, a slightly firmer pad can be the better choice if the softer one lets it wobble.
Ready to test your own design? Explore INKCLOUD TPU 95A Flexible Filament.