HT-PLA Pure Filament: How to Check Part Fit After Annealing?
XUCHUNHT-PLA Pure Filament: How to Check Part Fit After Annealing
A metal scoop handle drops neatly into your freshly printed stand. After heat treatment, the same handle catches at the mouth of the slot, or the stand rocks on the counter. Before scaling the entire model, find out which dimension changed. A slot that narrowed and a base that warped call for different revisions.
HT-PLA Pure filament is INKCLOUD’s high-temperature PLA. Its product page lists 190–230°C for the nozzle and 55–65°C for the build plate. It also advertises a Vicat softening temperature of up to 150°C. Vicat measures softening under specified test conditions. Use the filament maker’s separate annealing guidance for the heat-treatment cycle, and evaluate the finished part under the conditions where it will be used. INKCLOUD HT-PLA Pure product guide · ASTM Vicat test method
Test the slot at full size
For this project, the printed stand supports the far end of a metal scoop handle, with the bowl clear of the plastic. Take a short section of the model that includes the slot and some of the base. Keep the final wall thickness and print orientation. Print two copies from the same spool and keep one untreated as a reference.
Once the samples cool, measure the slot at its opening and where the handle rests. Record the height from the base to the bottom of the slot. Then set the sample on a flat surface and check whether it rocks. Test the real scoop handle, too. A measurement can tell you that the slot narrowed, while the handle can show exactly where it catches.
Measure again after the approved heat-treatment cycle
Obtain the annealing instructions for your exact filament before treating the sample. After the specified cycle and cooldown, repeat the same measurements at the same points. Annealing can change dimensions differently along different print axes, so record the changes separately. Prusa’s 3D print annealing experiments
| What you observe | What to try on the next sample |
|---|---|
| The handle catches only at the opening | Add a small lead-in chamfer and keep the seating area the same. |
| The handle binds where it rests | Widen the slot where it binds, then verify the revised fit after the same treatment. |
| The slot fits, but the stand rocks | Check the base for distortion. Review the treatment setup and the base geometry before changing the slot. |
| The handle fits but sits too low | Adjust the slot height while keeping the width that already works. |
Once the sample works, print and treat one full stand. Check fit and flatness again. The complete base can distort differently from the short sample. Before printing a batch, confirm that the stand holds the handle steadily and that the scoop can be lifted out without pulling the stand along with it.
Check food-contact requirements for the finished part
INKCLOUD describes HT-PLA Pure as a food-contact-grade filament and calls for checking processing, coatings, and the intended use before commercial deployment. For a part intended to touch food, verify the documentation for the exact filament and color, then evaluate the finished article for its intended food type, contact time, temperature, and cleaning conditions. This project keeps the printed stand in contact with the handle only. INKCLOUD HT-PLA Pure product guide · FDA guidance on food-contact substances
Frequently asked questions
Can I anneal HT-PLA Pure at 150°C?
Use the annealing schedule supplied for the exact formulation. The published 150°C figure refers to Vicat softening, which is measured under controlled test conditions. INKCLOUD HT-PLA Pure product guide · ASTM Vicat test method
Should I scale the entire model to compensate for shrinkage?
Start with the cooled sample measurements. If only the slot is tight, adjust that feature. If several dimensions change consistently, measure each axis before applying any broader compensation. Prusa’s annealing experiments
What should I record for the next batch?
Record the filament and color, print orientation, slicer profile, heat-treatment conditions, and cooled measurements. Keep one finished stand as a reference for fit and flatness.
Explore INKCLOUD HT-PLA Pure Filament for display models and functional prototypes where heat resistance and dimensional fit both matter.