3D Print Not Sticking to Bed on Ender 3? Choose the Right Leveling Path
XUCHUN3D Print Not Sticking to Bed on Ender 3? Choose the Right Leveling Path
If a 3D print is not sticking to the bed on an Ender 3, do not begin with a random Z-offset value or another model’s leveling tutorial.
“Ender 3” can refer to several generations of Creality printers. Some use four manual adjustment knobs. Some combine manual setup with a CR Touch probe. Newer V3 models use more automated calibration systems.
The correct procedure depends on the complete model name.
This article covers the decision process rather than providing one universal adjustment. Use the official manual and support page for your exact printer before changing hardware or firmware.
Step 1: Identify the Exact Ender-3 Model
Check the label on the printer, its startup screen, original order or manual.
| Ender-3 group | Typical leveling path | What to verify |
|---|---|---|
| Classic Ender-3, Pro and many V2 configurations | Four-corner manual adjustment | Knob adjustment, repeated corner checks and center result |
| Ender-3 S1 family | CR Touch-assisted leveling plus Z compensation | Probe operation, leveling cycle and final nozzle offset |
| Ender-3 V3 SE | Automatic leveling and automatic Z-offset workflow | Clean platform, completed leveling and first-layer result |
| Ender-3 V3 KE | Model-specific automatic calibration | Current KE manual and build-plate instructions |
| Ender-3 V3/CoreXZ generation | Automatic calibration with model-specific sensing | Official V3 troubleshooting path |
| Modified Ender-3 | Depends on installed probe, board and firmware | Documentation for the modification |
“Typical” does not guarantee the configuration of a used or modified printer. Inspect the actual machine.
Creality maintains separate download and support pages for different Ender-3 models. Creality Ender-3 download center
Checks That Apply Before Either Leveling Path
Before recalibration:
-
Allow the printer to complete any required startup procedure.
-
Remove loose filament or previous-print residue from the plate.
-
Check that the plate is installed and seated correctly.
-
Inspect the nozzle tip for attached plastic that could affect probing or the first layer.
-
Confirm that the slicer profile matches the printer and nozzle.
-
Confirm that the material profile matches the loaded filament.
-
Save the current project and any custom values.
Do not level against residue on the nozzle or plate. The printer may measure the residue instead of the intended surfaces.
Path A: Classic Ender-3 Manual Bed Leveling
Creality’s original Ender-3 instructions describe a four-corner manual process: home the printer, release the motors as instructed, move the nozzle to each adjustment point and use paper as a contact reference. The corners are checked repeatedly because changing one knob can influence another area. Creality’s original Ender-3 bed-leveling instructions
Follow the sequence in the manual for the exact printer.
What you are trying to achieve
The goal is consistent nozzle-to-plate contact across the usable area—not a particular number of knob turns.
After the corner procedure, print a first-layer test that covers several locations.
Look for:
-
Similar line width across the test
-
Adjacent lines joining consistently
-
No missing or extremely thin areas
-
Nozzle movement without scraping
-
No patch being dragged behind the nozzle
If the center differs from the corners
Repeat the procedure to confirm that the difference is consistent.
A center-only problem does not prove that the plate is warped. Check plate seating, debris underneath, surface condition and the repeatability of the manual adjustment before replacing parts.
Do not immediately install “upgraded” springs
Replacement springs, spacers or adjustment wheels change the machine. They should not be the first response to a single adhesion failure.
First establish whether the stock adjustment can produce a repeatable first layer.
Path B: Ender-3 S1 and CR Touch-Assisted Models
The Ender-3 S1 documentation uses CR Touch automatic leveling followed by verification or adjustment of the Z-axis compensation.
Automatic probing measures differences across the plate. It does not clean contamination, select the filament profile or guarantee the correct final nozzle contact.
Creality’s S1 documentation instructs users to run the automatic leveling process and then set the nozzle-to-platform relationship through the Z-offset procedure. Creality Ender-3 S1 manual
Correct order
-
Inspect the probe and make sure it can deploy without obstruction.
-
Clean the nozzle and platform as required.
-
Run the model’s automatic leveling procedure.
-
Check the resulting first layer.
-
Adjust the supported Z compensation only when the appearance justifies it.
-
Save the value according to the machine’s instructions.
Do not copy a Z-offset number from another S1. The value describes the geometry of an individual machine.
If CR Touch behaves abnormally
Stop adjusting the Z offset and use Creality’s probe troubleshooting procedure. A failed or inconsistent probe measurement cannot be corrected reliably by guessing a larger offset.
Path C: Ender-3 V3 SE Automatic Leveling
The V3 SE manual describes a leveling cycle that includes nozzle heating, nozzle cleaning and automatic Z-offset measurement. It also advises cleaning the platform before leveling so foreign material does not influence the result. Creality Ender-3 V3 SE manual
If the automated result produces a poor first layer:
-
Confirm that the nozzle was clean during measurement.
-
Confirm that the plate contained no residue.
-
Repeat the official leveling process.
-
Observe whether the problem affects the whole plate or one location.
-
Use only the supported compensation adjustment.
-
Record the original value before changing it.
Creality’s V3 SE troubleshooting guide identifies inaccurate Z compensation and unusually inconsistent leveling data as areas requiring specific diagnosis. Do not apply its firmware or mechanical instructions to another Ender-3 model. Creality Ender-3 V3 SE troubleshooting guide
Path D: Ender-3 V3 and Other Newer V3 Models
Creality’s current Ender-3 V3 support page has a dedicated topic covering first-layer adhesion, models not sticking and nozzle scraping. Its troubleshooting information includes platform contamination, mismatched slicing parameters and abnormal leveling among the areas to investigate. Creality Ender-3 V3 support guide
Use the page for the exact V3 variant. Do not assume that V3, V3 SE and V3 KE share identical sensors, firmware menus or calibration sequences.
Start with the printer’s own calibration function and recommended profile. Escalate to component inspection only when the official diagnostic path supports it.
Read the First Layer Before Adjusting Z Offset
Lines remain round and separate
The nozzle may be too far from the plate, but also check for interrupted extrusion and an incorrect profile.
Lines are heavily ridged
The nozzle may be too close. Moving it closer will not improve adhesion.
Material is missing in places
Determine whether the nozzle is restricting flow or the filament is not being delivered consistently.
One area fails while the rest succeeds
Investigate plate seating, residue and the repeatability of leveling data.
The first layer succeeds but corners lift later
This is more consistent with a later warping problem than an initial leveling failure. Review geometry, cooling and material conditions.
Verify the Build Plate and Filament Profile
Ender-3 models have shipped with different build surfaces, and owners often replace them.
Identify the actual surface rather than assuming it is the original plate. Follow that plate manufacturer’s cleaning and material-compatibility instructions.
In the slicer, verify:
-
Exact printer model
-
Nozzle diameter
-
Material category
-
Plate or adhesion option where available
-
First-layer toolpath
-
Model orientation
Creality’s V3 troubleshooting guidance specifically notes that mismatching the physical material and slicing parameters can contribute to first-layer problems. Creality Ender-3 V3 troubleshooting guide
When choosing filament, compare the printer and surface requirements with the INKCLOUD filament collection. Changing filament does not fix an unresolved leveling fault, so keep material selection and machine diagnosis separate.
Should You Use Glue?
Use glue only when the documentation for the installed plate and material supports it.
Depending on the surface, glue may improve attachment or provide a protective separation layer. It is not a replacement for correct leveling or Z compensation.
Apply only the recommended product and amount. Record whether the plate was cleaned or coated before the comparison test.
A Controlled Ender-3 Adhesion Test
After following the correct leveling path:
-
Select the supported printer and material profile.
-
Print several small first-layer patches across the usable plate.
-
Photograph the result before removal.
-
Change one justified variable if needed.
-
Repeat the same file.
-
Confirm that the part releases safely after cooling.
Do not begin with a long model. A small test makes location-dependent errors easier to see and wastes less material.
When to Stop Adjusting
Contact Creality support or the component supplier when:
-
The probe cannot complete its self-check
-
Leveling data is abnormal or inconsistent
-
The nozzle approaches the plate unexpectedly
-
The bed or carriage appears physically deformed
-
A firmware error is displayed
-
The problem persists after the model-specific procedure
Send the exact model, firmware version, photographs, leveling result and project file.
Frequently Asked Questions
What Z offset should I use on an Ender 3?
There is no universal value. It depends on the printer, nozzle, probe, plate and assembly. Determine it through the procedure for the exact model.
Does Ender-3 automatic leveling replace manual setup?
It depends on the model. Some systems combine physical setup, probing and a final offset. Follow the manual for that printer.
Why does my Ender 3 print stick in the center but not the corners?
First confirm that the pattern repeats. Then check plate seating, debris, manual corner adjustment or automatic leveling data according to the model.
Should I update firmware to fix adhesion?
Only when Creality’s documentation for the exact model identifies a relevant firmware issue or support instructs you to do so. Do not install another model’s firmware.
Is this guide official Creality documentation?
No. It is an independent INKCLOUD help article that links to Creality’s official model-specific resources. Ender and Creality are trademarks of their respective owner.