3D Printing Problems List: 18 Common Issues and What to Check First

Use this 3D printing problems list to identify 18 common FDM issues, understand what each symptom means, and choose the first relevant check before changing multiple settings.

By XUCHUN

3D Printing Problems List: 18 Common Issues and What to Check First

XUCHUN

3D Printing Problems List: 18 Common Issues and What to Check First

When a print fails, the fastest response is not always changing a setting. The useful first step is naming the symptom and deciding which part of the process deserves attention.

This 3D printing problems list covers 18 common issues in filament-based FDM and FFF printing. Each entry includes a visual clue, a sensible first check, and a change to avoid making too early.

Use it as an index rather than a collection of universal settings. Exact temperatures, maintenance procedures, and build-surface requirements depend on the printer and filament.

Quick 3D Printing Problems List

No. Problem Main visual clue First area to check
1 No extrusion at the start No material leaves the nozzle Loading and nozzle clearance
2 First layer not sticking Lines move with the nozzle Surface preparation and calibration
3 First layer too compressed Ridges and material pushed sideways Nozzle-to-bed distance
4 Uneven first layer Quality changes across the plate Plate seating and calibration
5 Under-extrusion Missing material in walls Filament path and profile
6 Extrusion stops mid-print Print continues without material Feeder, spool and possible restriction
7 Warping Corners curve upward Material conditions and base geometry
8 Layer shifting Upper section moves sideways Axis movement and collision evidence
9 Spaghetti failure Filament accumulates in open air Earliest detached or collapsed feature
10 Supports fail Supported feature loses its foundation Orientation and support preview
11 Stringing Fine hairs between separate features Material condition and travel behavior
12 Blobs or zits Small raised marks on walls Seam placement and extrusion consistency
13 Ringing or ghosting Repeated ripples near corners Motion and machine stability
14 Poor bridging Horizontal spans sag Span, orientation and bridge settings
15 Top-surface gaps Infill remains visible through the top Top structure and extrusion consistency
16 Layer separation Part splits along layer lines Material profile and cooling
17 Dimensional error Features print at the wrong size Model, slicer and measurement method
18 Weak or brittle part Part breaks below expected load Material condition, orientation and design

A visible symptom can have several causes. This table selects an investigation path; it does not confirm the diagnosis.

First-Layer Problems

1. No extrusion at the start

What it looks like: The nozzle moves, but little or no plastic appears.

Check first: Confirm that filament is loaded and that the nozzle is not being held so close to the plate that material cannot exit.

Do not change yet: Avoid increasing flow before confirming that extrusion is physically possible.

A nozzle positioned too close can restrict the opening. First-layer setup should follow the calibration procedure for the specific printer. Prusa’s first-layer guide

2. First layer not sticking

What it looks like: Fresh lines remain rounded, curl behind the nozzle, or move around the plate.

Check first: Verify build-surface compatibility, approved cleaning procedures, plate seating and first-layer calibration.

Do not change yet: Do not keep lowering the nozzle simply to force adhesion. Excessive compression can restrict extrusion or damage a surface.

3. First layer too compressed

What it looks like: Plastic forms ridges, rough patches or material that is pushed aside by the nozzle.

Check first: Compare the result with the printer manufacturer’s first-layer examples.

Do not change yet: Avoid compensating with a lower flow rate before correcting the nozzle-to-bed relationship.

4. Uneven first layer

What it looks like: One area appears acceptable while another has gaps, ridges or poor attachment.

Check first: Inspect the affected location, plate seating and calibration. Check for debris beneath a removable plate.

Do not change yet: A global temperature or extrusion change is unlikely to explain why only one location fails.

Problems That Develop During Printing

5. Under-extrusion

What it looks like: Walls contain gaps, deposited roads are incomplete, or sections appear thin.

Check first: Inspect spool movement, the filament path, the feeder and the selected printer, material and nozzle profile.

Do not change yet: Increasing the extrusion multiplier can hide the symptom without correcting interrupted material delivery.

Prusa lists calibration, slicer settings, the nozzle, extruder gears, hotend cooling and filament among the areas associated with under-extrusion. Prusa’s under-extrusion guide

6. Extrusion stops mid-print

What it looks like: The printer continues moving, but new layers are missing.

Check first: Determine whether the spool is trapped, filament has been damaged at the feeder, or the extrusion path is restricted.

Do not change yet: Do not push tools into a hotend without following the printer manufacturer’s procedure.

7. Warping

What it looks like: Corners or edges lift after the base initially appeared attached.

Check first: Review material requirements, base geometry, build-surface preparation and environmental conditions.

Do not change yet: Disabling cooling or raising bed temperature is not a universal fix.

Warping involves deformation as the printed material cools and contracts. The appropriate response depends on the material, geometry and machine. Prusa’s warping guide

8. Layer shifting

What it looks like: All geometry above one layer is displaced sideways.

Check first: Record the shift direction. Look for an obstruction, collision, belt issue or unsecured pulley using the machine’s maintenance instructions.

Do not change yet: Do not tighten every belt as far as possible.

Layer shifts are associated with abnormal X- or Y-axis movement; identifying the affected direction helps focus the inspection. Prusa’s layer-shifting guide

9. Spaghetti failure

What it looks like: Loose filament collects around the printer instead of forming the model.

Check first: Find the lowest failed area. Determine whether the part detached, a support collapsed or a narrow feature broke.

Do not change yet: Do not treat the tangled filament as the original problem. It is usually the result of an earlier failure.

10. Supports fail

What it looks like: Supports detach, collapse or fail to reach the feature they should hold.

Check first: Inspect the slicer preview and consider whether another orientation or a divided model would reduce difficult supports.

Do not change yet: Avoid increasing support density everywhere before locating the unsupported feature.

Surface-Quality Problems

11. Stringing

What it looks like: Fine threads connect separate towers, openings or parts.

Check first: Inspect nozzle cleanliness, material condition and the correct temperature and retraction profile.

Do not change yet: Do not make a large retraction adjustment based on a profile from a different extrusion system.

Moisture can contribute to stringing, roughness and inconsistent extrusion, although stringing alone does not prove the spool is wet. Polymaker’s wet-filament guide

12. Blobs or zits

What it looks like: Small raised marks appear at repeated or irregular locations on an outer wall.

Check first: Compare the marks with seam locations in the slicer preview and look for inconsistent extrusion.

Do not change yet: Avoid lowering flow globally if most of the wall is already correct.

13. Ringing or ghosting

What it looks like: Fading ripples repeat after a sharp corner or direction change.

Check first: Confirm that the printer is on a stable surface and inspect the machine according to its maintenance guide. Note whether the issue appeared after selecting a faster profile.

Do not change yet: Do not confuse ringing with an actual layer shift; ringing does not move the entire upper portion of the part.

14. Poor bridging

What it looks like: Lines sag beneath a horizontal unsupported span.

Check first: Review span length and orientation. Consider suitable supports or local bridge controls.

Do not change yet: Avoid changing the entire material profile for one bridge.

Shorter bridges are generally easier, and orientation can sometimes remove the bridge completely. Prusa’s bridging guide

15. Top-surface gaps

What it looks like: Infill remains visible or the top contains open lines.

Check first: Inspect the slicer preview for the intended top structure and confirm that extrusion is otherwise consistent.

Do not change yet: Avoid increasing flow before determining whether the problem is limited to the top or affects the whole part.

Problems Found After Printing

16. Layer separation

What it looks like: A visible horizontal crack forms, or the part breaks between layers.

Check first: Confirm the correct material profile, review cooling and determine whether material was missing during printing.

Do not change yet: Do not assume every horizontal opening is weak bonding. It may be under-extrusion or a skipped section.

17. Dimensional error

What it looks like: A hole, slot or external feature differs from the intended size.

Check first: Verify the source model, slicer scaling, measurement method and whether the error affects one feature or every dimension.

Do not change yet: Do not scale the entire model to correct one hole. That also changes dimensions that may already be correct.

18. Weak or brittle part

What it looks like: The finished part breaks under less load than expected.

Check first: Review part orientation, geometry, material condition, profile and the direction of the applied load.

Do not change yet: More infill is not a complete answer. A failure through the walls or between layers may require a different investigation.

Choose material according to the application and printer. The INKCLOUD filament collection can be linked here so readers can compare available material categories after identifying their project requirements.

How to Use This List Without Creating New Problems

Choose the earliest symptom that appeared, then make one relevant check. Save the original project before changing a profile.

Use the same small test for comparisons where practical and record:

  • Printer, nozzle and build surface

  • Exact filament and storage history

  • Selected profile

  • Original symptom

  • One change

  • Result of the repeat test

A cleaner-looking print is not automatically a successful correction. For example, reducing stringing is not an improvement if extrusion no longer restarts reliably.

Frequently Asked Questions

Which 3D printing problem should I fix first?

Fix the earliest failure in the sequence. A detached base can later produce spaghetti, while under-extrusion can lead to weak walls. Later symptoms may be consequences.

Can one print have several problems?

Yes. Document each symptom, but investigate them in the order they appeared.

Should I copy settings from another printer?

Use the profile intended for your printer, nozzle and material as the baseline. Settings from another setup may be useful for understanding an idea but are not verified for yours.

When should I contact support?

Contact the printer or material supplier when the problem persists after the supported checks, when a component appears damaged, or when the next step involves unfamiliar electrical or mechanical work. Include photographs, the saved project and your test record.

Previous Next
Leave a comment 0 comments

    Read more articles