Dry Filament in AMS 2 Pro: Settings, Limits and Best Practices

Learn how to dry filament in an AMS 2 Pro, including preparation, power requirements, material limitations and troubleshooting. This guide also explains when its 65°C maximum temperature may not be enough.

By XUCHUN

Dry Filament in AMS 2 Pro: Settings, Limits and Best Practices

XUCHUN

Dry Filament in AMS 2 Pro: Settings, Limits and Best Practices

The AMS 2 Pro combines automatic filament management, sealed storage and active drying in one four-spool system. For users who frequently switch colors or materials, this can reduce the need to move spools between a separate dryer and the printer.

However, the AMS 2 Pro is not a universal drying solution.

Its maximum drying temperature is 65°C, while some engineering filaments require higher temperatures according to their technical data sheets. Power requirements and simultaneous printing behavior can also vary by printer model, system configuration and firmware version.

This guide explains how to dry filament in AMS 2 Pro without assuming that one setting works for every spool.

Can the AMS 2 Pro Actually Dry Filament?

Yes. Unlike a passive dry box, the AMS 2 Pro provides active heating and moisture discharge.

Its drying system includes:

  • Active heated drying

  • External air circulation

  • Automatic venting

  • Rotating spools for more even exposure

  • Temperature and humidity monitoring

  • Sealed storage after drying

  • Automatic drying presets for supported Bambu RFID spools

A passive storage box mainly slows additional moisture absorption. The AMS 2 Pro can actively remove moisture, provided that the material’s drying requirements fall within the system’s operating range.

The Most Important Limitation: 65°C Maximum

The AMS 2 Pro has a maximum drying temperature of 65°C.

That is sufficient for many common materials, but it does not mean every PLA, PETG, TPU, PA or composite spool can be dried correctly at the same setting.

The required condition depends on:

  • Exact polymer formulation

  • Manufacturer and product line

  • Additives and reinforcement

  • Initial moisture level

  • Spool construction

  • Recommended drying duration

  • Whether the filament can be used in an AMS feed path

If the manufacturer requires a temperature above 65°C, the AMS 2 Pro may only partially dry the material or may take longer without achieving the intended result.

Do not increase drying time indefinitely as a substitute for reaching the required temperature. Use equipment capable of meeting the product’s documented drying condition.

AMS 2 Pro vs AMS HT

Feature AMS 2 Pro AMS HT
Spool capacity Four spools One spool
Maximum temperature 65°C 85°C
Main purpose Multi-material feeding, storage and drying Higher-temperature drying and feeding
Best suited to Multiple common materials and colors More demanding materials requiring higher temperatures
RFID support Supported Supported
Active moisture discharge Supported Supported

The AMS 2 Pro is more convenient for managing four compatible spools. The AMS HT has a higher maximum temperature and may be more appropriate when the material’s technical data sheet requires more than 65°C.

Neither device should be selected by material name alone. Check the exact product requirements first.

Drying Compatibility and Feeding Compatibility Are Different

A filament may be thermally suitable for drying in the AMS 2 Pro but still be unsuitable for automatic feeding.

Potential feeding concerns include:

  • Very soft generic TPU or TPE

  • Damp PVA or BVOH

  • Extremely brittle filament

  • Abrasive composite materials

  • Oversized or undersized spools

  • Cardboard spools that create dust or excessive friction

  • Spools that do not rotate smoothly

  • Tangled or poorly wound filament

Do not assume that “can be dried” automatically means “can be printed through the AMS.”

Check both:

  1. The material’s drying requirements.

  2. The AMS feeding compatibility for that exact product.

Before Starting a Drying Cycle

1. Identify the exact filament

Record the:

  • Material type

  • Manufacturer

  • Product line

  • Color

  • Reinforcement or additives

  • Spool construction

“PETG” or “nylon” alone is not enough information because different formulations may have different drying requirements.

2. Read the technical data sheet

Look for:

  • Recommended drying temperature

  • Recommended drying time

  • Maximum spool temperature

  • Whether drying is required before printing

  • Recommended storage humidity

  • AMS compatibility

Use the filament manufacturer’s information instead of copying settings from an unrelated spool.

3. Confirm that 65°C is sufficient

If the required drying temperature is higher than the AMS 2 Pro limit, use a suitable higher-temperature dryer or other manufacturer-approved equipment.

The AMS 2 Pro should not be expected to compensate for an insufficient temperature simply by running for an arbitrary period.

4. Inspect the spool

Check for:

  • Cracked or warped flanges

  • Loose filament

  • Crossed windings

  • Cardboard dust

  • Labels that may detach

  • Incorrect spool width or diameter

  • Resistance when rotating

A spool that binds against the enclosure or rollers will not rotate correctly during drying.

5. Check firmware and power

Make sure the printer and AMS firmware support the required drying controls.

Power requirements depend on the connected printer. Bambu Lab documentation states that an H2-series printer can power one AMS 2 Pro for drying through the 6-pin connection. Additional drying units require separate power adapters.

For documented X1- and P1-series configurations, an official AMS 2 Pro power adapter is required for the drying function.

Because compatibility and firmware behavior can change, check the current documentation for your exact printer before purchasing accessories.

How to Dry Filament in AMS 2 Pro

The precise interface may differ by printer and firmware, but the general workflow is as follows.

Step 1: Load compatible spools

Place each spool correctly on its rollers and make sure it can turn without contacting the lid or adjacent parts.

If drying multiple spools together, group materials that share compatible drying conditions. All four positions use the same drying environment, so conflicting material requirements should not be combined in one cycle.

Step 2: Close the lid

The lid must be closed correctly for the system to control airflow and temperature.

Inspect the seal and make sure no filament, label or foreign object is trapped along the edge.

Step 3: Keep the air path clear

During active drying, the AMS 2 Pro removes moisture through external air circulation.

Do not block:

  • Air inlets

  • Exhaust vents

  • Space around the unit

  • Required ventilation openings

Placing objects against the vents may reduce drying efficiency.

Step 4: Select the material

For supported Bambu RFID spools, the system can identify the filament and suggest a drying preset.

For third-party filament, enter or select the condition manually using the product’s technical data sheet. Do not assume the automatic preset for a similarly named material is correct.

Step 5: Review temperature and time

Before starting, confirm:

  • The temperature does not exceed the filament recommendation

  • The spool can tolerate the selected condition

  • The duration matches the manufacturer guidance

  • Every spool in the chamber is compatible with the same cycle

Do not use the highest available temperature automatically.

Step 6: Start and monitor the cycle

During drying, the system heats the chamber, manages airflow and rotates the spools.

Check periodically for:

  • Normal spool rotation

  • Unexpected noise

  • Filament unwinding

  • Spool deformation

  • Detached labels

  • Error messages

  • Blocked vents

  • Power warnings

Stop the cycle if a spool deforms, filament windings begin to fuse or the unit reports a persistent error.

Step 7: Keep the filament protected afterward

After drying, the AMS 2 Pro can act as sealed storage. Keep the lid closed and maintain the desiccant according to the manufacturer instructions.

Repeatedly opening the lid allows humid room air to enter. Load and unload spools efficiently, then close the system promptly.

Can You Dry Four Spools at Once?

The AMS 2 Pro is designed as a four-spool system, but drying four spools together is only appropriate when:

  • Every spool fits correctly

  • All spools rotate freely

  • The materials share compatible drying conditions

  • None of the spools exceed the temperature limit

  • The airflow path remains unobstructed

Avoid combining a low-temperature material with an engineering filament that requires a much hotter condition.

When the spools have different requirements, dry them in separate groups.

Can You Dry While Printing?

There is no single answer that applies to every AMS 2 Pro installation.

The result may depend on:

  • Printer model

  • Current firmware

  • Whether the AMS is actively feeding

  • Whether it is assigned for automatic refill

  • Number of connected AMS units

  • Available power

  • Presence of an external power adapter

Some configurations may prevent drying from an AMS that is actively participating in the current print. Other firmware versions may allow concurrent operation with reduced drying power or temperature.

Because this behavior has changed over time, follow the current on-device message and the latest official documentation for the exact printer.

For the most predictable result, complete the drying cycle before printing or use a separate, correctly powered AMS that is not participating in the print job.

Using Third-Party Filament

Third-party filament can be considered when:

  • The spool dimensions fit the AMS 2 Pro

  • The spool rotates reliably

  • The material is compatible with the feeding system

  • The required drying temperature is no higher than 65°C

  • The manufacturer provides suitable drying instructions

RFID-based automatic presets generally apply to supported Bambu filament. Third-party spools normally require manual material and drying settings.

Do not identify an unknown filament based only on color. Two visually similar spools may have completely different drying limits.

When evaluating new filament, review the product information before loading it into the AMS. You can browse INKCLOUD 3D printing filaments and compare each material’s specifications with the latest AMS 2 Pro requirements.

Compatibility should be confirmed for the specific spool; it should not be assumed for an entire brand or material family.

How to Tell Whether Drying Worked

Use a controlled before-and-after print.

Before drying, record:

  • Popping or hissing

  • Stringing

  • Surface roughness

  • Bubbles in extruded filament

  • Weak layer bonding

  • Inconsistent extrusion

After drying, print the same model with the same:

  • G-code

  • Nozzle

  • Build plate

  • Temperature

  • Speed

  • Retraction settings

  • Cooling settings

If the result improves, moisture was likely contributing to the problem.

If there is no meaningful improvement, inspect other causes such as retraction, excessive nozzle temperature, a partial clog or feed resistance.

Common AMS 2 Pro Drying Problems

Drying does not start

Check:

  • Firmware version

  • Printer compatibility

  • Cable connections

  • Power-adapter requirements

  • Whether another AMS operation is active

  • Messages on the printer or software interface

Do not substitute an unverified power adapter merely because its connector fits. Use equipment approved for the system.

The chamber does not reach the expected condition

Possible causes include:

  • Insufficient power

  • Blocked air inlet or vent

  • Lid not fully closed

  • Large temperature loss to the room

  • Multiple units sharing limited printer power

  • A sensor reading being interpreted incorrectly

The displayed value may represent a sensor location rather than the temperature at the center of every spool.

Humidity does not fall immediately

During the early part of a cycle, moisture leaving the filament enters the chamber air before being exhausted. The humidity reading may therefore change gradually rather than dropping instantly.

A stable low reading does not prove that moisture deep inside a thick spool has already been removed.

One spool does not rotate

Inspect:

  • Spool dimensions

  • Roller contact

  • Cardboard deformation

  • Tangled filament

  • Loose filament loops

  • Adjacent-spool interference

  • Whether the filament is still locked in a feed path

Do not force the spool to turn while the mechanism is powered.

Filament is still stringing after drying

Stringing may also result from:

  • Excessive nozzle temperature

  • Insufficient retraction

  • Incorrect travel settings

  • A worn nozzle

  • Material left in the nozzle

  • Inconsistent extrusion

  • A drying temperature below the material requirement

Treat moisture as one possible cause, not the only cause.

The spool deforms

Stop the cycle and check:

  • Selected temperature

  • Spool material

  • Local heat exposure

  • Manufacturer temperature limit

  • Whether an adapter changed the spool’s contact with the rollers

The spool may have a lower temperature limit than the filament.

Best Practices for Repeatable Results

  • Use settings from the exact filament manufacturer.

  • Group only materials with compatible drying conditions.

  • Keep vents unobstructed during active drying.

  • Maintain the desiccant for sealed storage.

  • Avoid unnecessary repeated heating.

  • Record when each spool was dried.

  • Update printer and AMS firmware carefully.

  • Check power requirements for the connected printer.

  • Test print before changing multiple slicer settings.

  • Use a higher-temperature dryer when 65°C is insufficient.

Frequently Asked Questions

Is AMS 2 Pro a real filament dryer?

Yes. It provides active heating and moisture discharge rather than functioning only as a passive storage box.

What is the maximum AMS 2 Pro drying temperature?

The specified maximum is 65°C.

Is 65°C enough for nylon?

It depends on the exact nylon formulation. Some nylon products require higher temperatures. Check the product’s technical data sheet; do not apply one answer to every PA or nylon filament.

Can it dry four different materials together?

Only when all four materials and spools share compatible temperature and duration requirements. Otherwise, divide them into separate cycles.

Can I dry generic TPU in AMS 2 Pro?

Do not assume so. Soft generic TPU may be unsuitable for automatic feeding, and its drying requirements may differ from TPU designed specifically for AMS use.

Can AMS 2 Pro replace a separate dryer?

It can replace a separate dryer for materials whose requirements fall within its operating range. It cannot fully replace higher-temperature equipment for every engineering filament.

Does RFID work with third-party filament?

Third-party spools generally do not provide Bambu’s automatic RFID drying presets. Enter settings manually according to the filament manufacturer.

Does the AMS keep filament dry after the cycle?

It can provide sealed storage after drying, but the lid, seals and desiccant must be maintained. Opening the enclosure repeatedly introduces humid air.

Do I need an external power adapter?

It depends on the printer and number of connected units. H2-series configurations can power one unit through the printer according to Bambu documentation, while additional units require adapters. Documented X1/P1 drying configurations require a separate official adapter. Verify the latest instructions for the exact setup.

Final Takeaway

The AMS 2 Pro is most useful when its three functions are treated separately:

  1. It actively dries compatible filament.

  2. It protects dried filament in sealed storage.

  3. It manages multiple materials during printing.

Its 65°C maximum is the main technical boundary. Confirm both drying compatibility and feeding compatibility before loading a spool, and do not rely on material names or automatic presets alone.

When a filament requires more heat than the AMS 2 Pro can provide, use a suitable higher-temperature drying system instead of assuming that a longer cycle will produce the same result.

Previous Next
Leave a comment 0 comments

    Read more articles